[China Glass Net] The frameless glass door is a type of glass door. It differs from other aluminum alloy glass doors in that there is no border around the door leaf of the frameless glass door. The installation method of the frameless glass door is similar to the general glass door installation method, but there are some differences. The installation method and installation points of the frameless glass door, you need to read carefully, you may use it.
Frameless glass door installation method
1. Positioning of the pay-off line: At the beginning of installation, the frameless glass door must be positioned for the fixed glass partition and the movable glass door fan. The position of the door frame is determined, and the ground level and the top level of the door frame are accurately measured.
2. Install the limit groove on the top of the frameless glass door frame: take the two metal decorative board edges from the center line of the bullet, and then install the limit groove at the top of the door frame according to the edge line.
3. Install the wooden bottom of the frameless glass door metal finish: nail the square wood on the original pre-buried wood brick, or fix the square wood on the ground by expanding the bolts, and then use the multi-purpose glue to metal the veneer. Stick to the wooden side.
4. Install the rigid door frame: nail the door frame according to the center line of the bullet, and then use plywood to determine the size and position of the door frame column. When it is fixed, the metal decorative surface is then wrapped.
5, glass door leafless glass door installation: use a glass suction cup (or glass suction cup machine) to suck the thick glass, then hold the suction cup to lift the thick glass plate through 2 to 3 people and erect it to The installation site is in place.
6. Glass fixing: Two flat wooden strips on the bottom and bottom of the bottom are sandwiched by thick glass, but a thick space of 4 mm is required to leave a thick glass plate, and then the multifunctional strip is applied on the flat wooden strip. The glue sticks the veneered metal plate to the square wood and the two flat wooden strips.
7. Injection glass seal: Inject the glass glue into the gaps on both sides of the top root groove and on both sides of the glass tray and the joint between the thick glass and the door frame column.
8. Docking between glass of frameless glass door: thick glass plate with fixed part, because the width is too large, it must be assembled by two or more pieces. The two pieces of aligned stitching must form seams and seams. Should leave a distance of 2 ~ 3mm.
Installation points of frameless glass door
1. Before all the installation steps are started, it must be ensured that the other processes of the interior decoration and decoration are basically completed before the construction is completed, and the positioning of the alignment should be strictly in accordance with the design drawings.
2. The width of the limit groove at the top of the frameless glass door frame should be greater than the thickness of the glass by 2 to 4 mm, and the groove depth is between 20 and 30 mm for injection.
3. When wrapping the metal decorative surface, place the decorative face-to-head seam in the middle of the sides of the mounting glass. The seam location must be accurate and vertical.
4. When installing the glass door leaf of the frameless glass door, the method of positioning should be: insert the upper part of the glass into the limit groove at the top of the door frame, then place the lower part of the glass on the center line on the bottom support, and the two sides are good. The installation position of the door frame is such that the sides of the thick glass cover the metal frame of the door frame facing the seam, and it is required that the seam joints are not visible inside or outside.
5. When sealing the glass seal, the injection sequence should be terminated from the end of a certain gap to the end, and must not stop in the middle.
6. During the docking process between the glass of the frameless glass door, the glass cut of the joint must be used, and after the glass is fixed, the glass should be glued into the gap. After filling, the plastic sheet should also be used. Scrape flat so that the gap forms a clean, uniform straight line, and the glass surface should be cleaned with a clean cloth.
Iron On Seam Sealing Tape,Seam Sealing Tape For Fabric,Automotive Seam Sealer Tape,Jual Seam Seal Tape
Jiangmen M.F.B.S. Machinery Ltd. , https://www.newpowerhk.com